How To Instal Over The Range Microwave Oven

Download Article

Download Article

An over-the-range microwave oven makes efficient use of space in your kitchen, while besides incorporating lighting and ventilation. After you brand sure you have the supplies you need for installation, double-check that your microwave will fit properly above your range. Mount the microwave in place using a template and bracket, and a few simple tools.

1. 1

   Plow off the power. Since a microwave is an electric appliance, you will need to take care to avert electrocution or other impairment. Before you kickoff installation, go to your circuit breaker, and flip the billow for the range to the "off" position.^[1]

2. 2

   Make sure there's an outlet nearby. Most over the range microwaves include a curt power string that is designed to feed upwards into the cabinet that the appliance volition sit underneath. Ideally, there will be an electrical outlet inside this cabinet that you lot can plug the power cord into.^[2]

   • Your microwave'south installation instructions will specify whether at that place are adequate alternative locations for the electric outlet.
   • If there is not an outlet in a convenient location, contact an electrician for assistance installing one before yous put the microwave in identify.

   Advertizing

3. 3

   Cheque to make certain your microwave can be installed at the proper height. ^[3] In full general the bottom of the microwave should be no college than 54 inches (140 cm) from the flooring. In addition, in that location should be approximately 20 inches (51 cm) to 24 inches (61 cm) betwixt the bottom of the microwave and the top of the range. This will allow you to use both the microwave and the range safely and comfortably.^[four]

   • Use a record mensurate to verify the height of your microwave.
   • Measure from the lesser of the cabinet you will install the microwave below to the height of the microwave. Brand a mark at this spot.
   • Measure the distance between this mark and the floor, and the superlative of your range, to make sure that the microwave volition be situated inside the acceptable height range.

4. 4

   Determine the ventilation direction. The microwave itself will have a fan, and since it sits above the range (where a range hood would normally go), both appliances volition accept to ventilate exterior together. Usually, there are two options: either the appliances will ventilate horizontally through a tube in the wall, or vertically, first through the cabinet above the microwave and then the ceiling or in a higher place on the wall.^[5]

   • Your microwave may have additional fittings which you should set in place in guild to let it to ventilate properly. Check the installation instructions that come with your particular model to be sure.
   • If yous practice not already have a ventilation organization in identify, contact a contractor to take one installed.^[6]

5. 5

   Reframe the opening, if necessary. If your kitchen cabinetry and framing are sturdy, they may be sufficient to support a relatively heavy over the range microwave. If the materials are less robust, reframe the area where you volition install the microwave with two by fours. Some experts recommend reframing in all cases.^[7]

   • Your microwave should come with a kit that has a framing template. Place it where y'all desire the microwave to sit, and follow the guidelines to cut through the drywall.
   • Remove the drywall and pull out the insulation from the area within the wall.
   • Secure ii by fours between the wall studs. Cheque the instructions provided with your microwave for the exact dimensions.
   • Make full in whatever empty infinite with new insulation.

   Advertisement

1. i

   See if your microwave has an installation template or wall plate. Your model should come with a template to assist guide you when installing mounting hardware. Place this on the wall, and the template should tell you where to place the hardware. Some models also come with a mounting subclass that volition have pre-drilled holes then you can hands screw it in place.^[8]

   • Use a level to make sure that the template is foursquare and that the microwave will sit properly in place.^[9]

2. two

   Find at to the lowest degree one stud. If you didn't reframe the installation site, you'll need to attach the mounting hardware to at least ane stud in the wall. Use an electronic stud finder, or gently tap on the wall with a hammer. When the taps sound tiresome instead of hollow, you lot have located a stud. Mark the site on the wall.^[ten]

   • Studs are ordinarily 16 inches (41 cm) inches apart on the wall. In one case you find one, measure sixteen inches to the either side to marking others.
   • Using your template, make sure that the hardware will be mounted on at to the lowest degree 1 of the studs. If not, reframe the site or contact a contractor for help.

3. 3

   Drill holes in the template or attach the wall plate. ^[eleven] Commonly, over the range microwaves will be installed using toggle bolts. Predrilling holes for these bolts will make installation easier--just follow the guidelines on your template. If yous are using a wall plate, go ahead and install that using the hardware and guidelines given in your model'southward instructions.^[12]

   • Near likely, you will demand a couple of drill bits: smaller ones for the toggle bolts, and a larger one to brand a pigsty to feed the microwave's power cord through the cabinet above the appliance (if there isn't already one). Bank check your model's instructions, and e'er use the recommended tools.

4. 4

   Set the microwave into position or onto the wall plate. It volition help to take another person to assist yous agree up the microwave.^[13] Push it upwardly and bring it up to the lesser of the cabinet. If your model has a wall plate, fit information technology into the bracket that will assist concur it in place. Brand sure that someone keeps holding the microwave in place for now.^[14]

5. 5

   Plug in the microwave. Feed the microwave's power cord through the hole drilled in the lesser of the cabinet above the appliance. Plug the cord into the outlet within the cabinet, just don't turn the power back on yet.^[15]

6. half dozen

   Thread bolts through the bottom of the cabinet. Feed the bolts (or screws) supplied with your microwave (or recommended by its instructions) into the holes y'all previously drilled in the bottom of the cabinet. They should slip into slots in the peak of the microwave. Tighten them using a wrench (or screwdriver) until the microwave is securely held in place.^[16]

   • Carefully let become of the microwave at this point to make sure that it stays in place.

7. 7

   Connect the blower. Slide the exhaust fan supplied with your microwave into place at the ventilation site. Specifications will vary from model to model, so read the instructions provided with yours. Most manufacturers also recommend using an approved sealant around the edges of the fan'south housing to brand the connection impervious.^[17]

   • You may need to take the fan out and change its direction, depending on the orientation of your ventilation system.

8. 8

   Test the microwave. At this point, you can finally flip the excursion for the range back to the "on" position. Verify that your microwave is getting power, and test it by heating something to brand sure that the appliance is working properly.

   • If your apparatus does not seem to work properly, read the troubleshooting section of the manual, if information technology has one, or contact the manufacturer.

   Advertising

Add New Question

• Question

  Can I install an over-the-range microwave by myself?

  

  Gevorg Grigorian is an Appliance Repair Specialist and the Owner of G and R Appliance Repair in Los Angeles, California. With over 12 years of experience, Gevorg specializes in residential and commercial appliance repairs also as heating, ventilation, and air conditioning (HVAC) services. Gevorg holds a BS in Business Administration and Direction from California State University-Northridge.

  

  Apparatus Repair Skilful

  Practiced Reply

Enquire a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertisement

Video

Things You'll Need

• A drill and ready of drill $.25
• A stud finder or lite hammer
• A screwdriver
• An adaptable wrench
• Toggle bolts
• A level
• A tape mensurate
• A drywall saw
• Sealant

Virtually This Article

Article Summary 10

Before you install an over-the-range microwave, brand certain it will be xx to 24 inches above the stovetop so they are both easy to employ. Then, use the microwave'due south installation template to marker where the mounting hardware should go. Next, attach the mounting hardware to at least one stud, which you can find using an electric stud finder, and lift the microwave onto it. Ship bolts through the cabinet above the microwave and slip them into the slots on top of the microwave to secure it. To learn how to install the ventilation system, keep reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 370,117 times.

Did this commodity aid you?

Source: https://www.wikihow.com/Install-an-Over-The-Range-Microwave

Posted by: whitewarchat.blogspot.com

Share this post